| BAE SYSTEMS INFORMATION AND ELECTRONIC SYSTEMS INTEGRATION INC. | 80249 |
| NAVAIR AND NAVSEA MANAGED ORIGINAL DESIGN ACTIVITY DWG NOT MATERIAL/PARTS SUPPLIER | 10001 |
| RAYTHEON COMPANY | 49956 |
| RAYTHEON COMPANY | 49956 |
| RAYTHEON COMPANY | 96214 |
| NAVAIR AND NAVSEA MANAGED ORIGINAL DESIGN ACTIVITY DWG NOT MATERIAL/PARTS SUPPLIER | 10001 |
| LOCKHEED MARTIN CORPORATION | 3538 |
| ROCKWELL AUTOMATION, INC. | 1121 |
| U S ARMY AVIATION AND MISSILE COMMAND | 18876 |
| CRL COMPONENTS INC | 71590 |
| HEICO OHMITE, L.L.C. | 44655 |
| ROCKWELL AUTOMATION, INC. | 1121 |
| ROCKWELL AUTOMATION, INC. | 1121 |
| NATIONAL WEATHER SERVICE | 82187 |
| MILITARY SPECIFICATIONS PROMULGATED BY MILITARY DEPARTMENTS/AGENCIES UNDER AUTHORITY OF DEFENSE STANDARDIZATION MANUAL 4120 3-M | 81349 |
| GENERAL ELECTRIC CO ELECTRONIC COMPONENTS DIVISION OF ELECTRONIC ATOMIC AND DEFENSE SYSTEMS GROUP | 24454 |
| BAE SYSTEMS INFORMATION AND ELECTRONIC SYSTEMS INTEGRATION INC. | 80249 |
| MILITARY SPECIFICATIONS PROMULGATED BY MILITARY DEPARTMENTS/AGENCIES UNDER AUTHORITY OF DEFENSE STANDARDIZATION MANUAL 4120 3-M | 81349 |
| MILITARY SPECIFICATIONS PROMULGATED BY MILITARY DEPARTMENTS/AGENCIES UNDER AUTHORITY OF DEFENSE STANDARDIZATION MANUAL 4120 3-M | 81349 |
| MILITARY SPECIFICATIONS PROMULGATED BY MILITARY DEPARTMENTS/AGENCIES UNDER AUTHORITY OF DEFENSE STANDARDIZATION MANUAL 4120 3-M | 81349 |
| SECTION QUANTITY | 1 |
| BODY STYLE | CYLINDRICAL BUSHING MOUNTED |
| RELIABILITY INDICATOR | NOT ESTABLISHED |
| III OVERALL LENGTH | 1.312 INCHES MINIMUM AND 1.562 INCHES MAXIMUM |
| BODY DIAMETER | 1.032 INCHES MINIMUM AND 1.156 INCHES MAXIMUM |
| SHAFT DIAMETER | 0.248 INCHES MINIMUM AND 0.251 INCHES MAXIMUM |
| SHAFT LENGTH | 0.844 INCHES MINIMUM AND 0.906 INCHES MAXIMUM |
| MOUNTING BUSHING LENGTH | 0.344 INCHES MINIMUM AND 0.390 INCHES MAXIMUM |
| BODY LENGTH | 0.468 INCHES MINIMUM AND 0.656 INCHES MAXIMUM |
| III OVERALL DIAMETER | 1.515 INCHES MAXIMUM |
| SHAFT STYLE | ROUND, SLOTTED |
| ACTUATOR TYPE | SINGLE SHAFT |
| MAXIMUM STARTING TORQUE | 6.00 INCH-OUNCES |
| MAXIMUM STOP TORQUE | 128.00 INCH-OUNCES |
| NONTURN DEVICE LOCATION | AT 9 OCLOCK |
| NONTURN DEVICE RADIUS | 0.515 INCHES MINIMUM AND 0.547 INCHES MAXIMUM |
| SCREW THREAD DIAMETER | 0.375 INCHES NOMINAL |
| SCREW THREAD SERIES DESIGNATOR | UNEF |
| SCREW THREAD QUANTITY PER INCH | 32 |
| TERMINAL LOCATION | RADIALLY POSITIONED OVER LESS THAN HALF THE CIRCUMFERENCE |
| MOUNTING METHOD | STANDARD BUSHING |
| ELECTRICAL RESISTANCE PER SECTION | 250.0 KILOHMS SINGLE SECTION |
| ROTARY ACTUATOR TRAVEL IN ANGULAR DEG | 309.0 MINIMUM AND 320.0 MAXIMUM |
| AMBIENT TEMP IN DEG CELSIUS PER SECTION AT ZERO PERCENT RATED POWER | 120.0 SINGLE SECTION |
| POWER DISSIPATION RATING PER SECTION IN WATTS | 2.0 FREE AIR SINGLE SECTION |
| RESISTANCE TOLERANCE PER SECTION IN PERCENT | -10.0 TO 10.0 SINGLE SECTION |
| ACTUATOR TRAVEL CONTROL FEATURE | STOPS |
| AMBIENT TEMP IN DEG CELSIUS PER SECTION AT FULL RATED POWER | 70.0 SINGLE SECTION |
| TERMINAL TYPE AND QUANTITY | 3 TAB, SOLDER LUG |
| SPECIFICATION/STANDARD DATA | 81349-MIL-R-94/5 GOVERNMENT SPECIFICATION |
| SPECIAL FEATURES | CAPACITOR,FIXED 2; CONNECTOR 1; PRINTED WIRING BOARD 1; RESISTOR,FIXED 30; TRANSISTOR 6 |
| STYLE DESIGNATOR | 20 RADIAL TERMINAL EACH END |
| GENERAL CHARACTERISTICS ITEM DESCRIPTION | ELLIPTICAL SHAPE; WITH 1 MTG HOLE |
| THREAD SERIES DESIGNATOR | UNJF |
| TEST DATA DOCUMENT | 81349-MIL-R-94 SPECIFICATION (INCLUDES ENGINEERING TYPE BULLETINS, BROCHURES,ETC., THAT REFLECT SPECIFICATION TYPE DATA IN SPECIFICATION FORMAT; EXCLUDES COMMERCIAL CATALOGS, INDUSTRY DIRECTORIES, AND SIMILAR TRADE PUBLICATIONS, REFLECTING GENERAL TYPE DATA ON CERTAIN ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS AND TEST CONDITIONS THAT ARE SHOWN AS "TYPICAL", "AVERAGE", "NOMINAL", ETC.). |
| A resistor in which a sliding or rolling contact moves over an exposed area of the resistive element to change the ohmic value of the output. The functional tolerance (linearity), if given, of the output is greater than plus or minus 1 percent on linear outputs. Specified outputs such as sine, cosine, tangent, etc., shall be considered to be precision. For items having manually positioned taps designed to be set and fixed prior to use, see RESISTOR, ADJUSTABLE. For items with step by step variation, see RHEOSTAT and RESISTOR, STEP BY STEP. For tandem-mounted items designed to function together as an attenuator (and rated accordingly), see ATTENUATOR, VARIABLE. Excludes RESISTOR (1), VARIABLE, WIRE WOUND, NONPRECISION; RESISTOR (1), VARIABLE, NONWIRE WOUND PRECISION; and RESISTOR (1), VARIABLE, WIRE WOUND, PRECISION. |
A-A-1191
$0.00